The VM-2120 is a multifunctional amplifier that can be mounted in an EIA-Standard equipment rack (3-unit size). The unit comes with 4 audio inputs including the background music input, and the speaker output section which has an internal attenuator and 5-zone selector.
It permits not only general-purpose broadcast, but also Emergency Broadcast based on the EN60849 Standard which gives pre-recorded voice instructions(*1) in the emergency situation. Broadcast can be made from an optional RM-200M Remote Microphone as well as from the amplifier, and can be remotely controlled from external equipment. In addition, for 100 V/83 Ω application the unit features the surveillance function(*2) which automatically checks the system for failures. (*1) An optional EV-200M Voice Announcement Board is required. (*2) An optional SV-200MA Surveillance Board is required.
Specifications
-
Power Requirement:AC mains, 50/60 Hz DC: 24 V
-
Output:120 W
-
Frequency Response:50 - 16,000 Hz
-
Distortion:Less than 1%
-
Signal-to-Noise Ratio:More than 60 dB
-
Tone Control:Bass: 100 Hz ±10 dB, Treble: 10 kHz ±10 dB (Inputs 1 - 3 and BGM individually adjustable.)
-
Remote Microphone/Extension Amplifier Connection:Two RJ45 female connectors Maximum distance: 800 m
-
Audio Input:
-
Inputs 1 ~ 3:-60 dB*1 [MIC]/-10 dB*1 [LINE] (switchable), 600 Ω, electronically balanced*2, combined XLR type connector (female)/ 1/4" phone jack (Only Input 1 is additionally (female)/ 1/4" phone jack (Only Input 1 is additionally equipped with DIN connector*3.)
-
Telephone Paging Input:Push-in terminal block
-
-10 dB*1, 10 k Ω, electronically-balanced*2
-
Control : No-voltage make contact input
-
BGM 1 - 2:-20 dB*1, 10 k Ω, RCA pin jack, monaural
-
Power Amplifier Input:0 dB*1, 10 k Ω, RCA pin jack
-
External Speaker Line Input:100 V line, for All-Zone Broadcast
-
Audio Output:
-
Speaker Output:83 Ω (100 V line, volume control in maximum position), Removable terminal block with screw terminals.
-
Speaker Zone Control:5-zone selector with attenuator
-
Direct Speaker Line Output:Direct output from the power amplifier output transformer
-
Line Output:0 dB*1, 10 k Ω, RCA pin jack
-
Recording Output:0 dB*1, 10 k Ω, RCA pin jack
-
Preamplifier Output:0 dB*1, 10 k Ω, RCA pin jack
-
Control Inputs 1 - 3:For controlling Inputs 1 - 3, Push-in terminal block
-
No-voltage make contact.
-
Control Input and Output:
-
Input : No-voltage make contact input
-
Output : Open collector output
-
(1) External control input
-
Activation of messages for an optional Voice Announcement Board*4
-
Activation of power
-
Activation and stop of Emergency Broadcast
-
Unit's broadcast cutoff (when activated by an external emergency equipment)
-
(2) Status output
-
Irregularity of communications with the Remote Microphone and an expansion amplifier
-
AC power condition
-
DC power condition
-
Irregularity of the sound source of the Voice Announcement board
-
Stop of the unit's broadcast
-
External Attenuator Control Output:Removable terminal block with screw terminals, relay, no-voltage make contact output, transfer type
-
Surveillance Input and Output*5:25-pin female D-sub connector
-
Input : No-voltage make contact input
-
Output : Open collector output
-
Power Output:24 V DC
-
Chime Tone:
-
Built-in chime:
-
2-tone chime/2-tone chime(fast repeat)
-
4-tone chime (Up)/Single-tone chime/4-tone chime (Up & Down)/Gong/off
-
Finish:
-
Panel: ABS resin
-
Case: Steel plate painted
-
Dimensions: 419 (W) × 143.3 (H) × 356.2 (D) mm
-
Notes:
-
*1 0 dB = 1 V
-
*2 Can be transformer-balanced with the addition of an optional IT-450 input transformer.
-
*3 For connection of the Paging Microphone with remote control switch.
-
*4 An optional EV-200 Voice Announcement Board is required.
-
*5 An optional SV-200M Surveillance Board is required.